Generally, it is possible for people to set up their own tracks. However, many people prefer to get a readymade section of the track. In the event that you go for creating your own rail, you need to ensure that you get rail joiner. The joiners are very crucial because they are the one that are used to join two or more sections together. The benefit of buying readymade joiners is that they came with drilled holes to fix your nuts and bolts. You therefore do not have to drill the holes since the manufacture have already done it for you.
The process of fixing these items is quite easy and straight forward. To start with, you need to check whether the two sections of the rail can slip together. Ensure that, when you are joining the two sections, you leave a space of about 3.175mm. You should then proceed to twisting the lock tabs below the snug fit. You should then ensure that you strongly tighten the grip using stainless screws.
Most people prefer the N scale snap track Atlas. This particular one has to be made using the joiners since wrapping of the metal beneath the tracks is necessary. The joint is placed on the middle of the track so that it remains well aligned and strong. Hiring a professional would be appropriate so as to ensure all the necessary measures and precautions are not ignored.
However, it is important for you to understand that, they are a bit complex to work with. This is purely because; they are made of soft metal. Nevertheless, they guarantee a tight fit. Ensure that you apply force to make them slip into the right place. However, you should avoid bending them since they may be hard to undo the bend them back.
The best method of installing them is to use needle nose pliers. Take one end using the pliers tip so that it sticks out straight from the end. Fit it to the end of the track and push slowly. If you encounter difficulties, try to swivel it a little on different sides until it starts to move. However do not swing it much.
It is worth noting that a joiner can only be used once since using it for the second time may be detrimental to the quality of the track since it will be normally very weak. As such, it is prudent to use them only once so that you do not compromise on the quality of your finished product.
It is a good idea to make sure you use screws during installation. This is normally done after you lay down your tracks. However, when the tracks get challenging, you can then choose to install the screws before.
Lastly, ensure that you fix two screws in each joiner. You need to make sure you fix them about halfway on both ends. This is important for you to get a better alignment and stronger well laid tracks. For you to prevent water from destroying the tracks, greasing is always recommended.
The process of fixing these items is quite easy and straight forward. To start with, you need to check whether the two sections of the rail can slip together. Ensure that, when you are joining the two sections, you leave a space of about 3.175mm. You should then proceed to twisting the lock tabs below the snug fit. You should then ensure that you strongly tighten the grip using stainless screws.
Most people prefer the N scale snap track Atlas. This particular one has to be made using the joiners since wrapping of the metal beneath the tracks is necessary. The joint is placed on the middle of the track so that it remains well aligned and strong. Hiring a professional would be appropriate so as to ensure all the necessary measures and precautions are not ignored.
However, it is important for you to understand that, they are a bit complex to work with. This is purely because; they are made of soft metal. Nevertheless, they guarantee a tight fit. Ensure that you apply force to make them slip into the right place. However, you should avoid bending them since they may be hard to undo the bend them back.
The best method of installing them is to use needle nose pliers. Take one end using the pliers tip so that it sticks out straight from the end. Fit it to the end of the track and push slowly. If you encounter difficulties, try to swivel it a little on different sides until it starts to move. However do not swing it much.
It is worth noting that a joiner can only be used once since using it for the second time may be detrimental to the quality of the track since it will be normally very weak. As such, it is prudent to use them only once so that you do not compromise on the quality of your finished product.
It is a good idea to make sure you use screws during installation. This is normally done after you lay down your tracks. However, when the tracks get challenging, you can then choose to install the screws before.
Lastly, ensure that you fix two screws in each joiner. You need to make sure you fix them about halfway on both ends. This is important for you to get a better alignment and stronger well laid tracks. For you to prevent water from destroying the tracks, greasing is always recommended.
No comments:
Post a Comment